Raspberry Pi 3 Model B+ overview
Bluetooth 4.2
The RPi3B supported Bluetooth 4.1; thanks to the CYW43455, the RPi3B+ now offers Bluetooth 4.2 – that is, "Bluetooth Classic" and Bluetooth LE (Low Energy). Version 4.2 improves speed, privacy, and data security for Bluetooth LE. Compared with the previous version, the data packets are two and a half times faster and are capable of containing up to 10 times more data.
Bluetooth 4.1 already provides for easier connection of devices without a hub, but Bluetooth 4.2 takes this to a whole new level: The IPSP-supported 6LoWPAN (Internet Protocol Support Profile/IPv6 over low-power wireless personal area networks) takes IPv6 to small, low-performance devices for integration into the Internet of Things.
The Generic Attribute Profile (GATT) provides a smart Bluetooth gateway to the Internet. For example, a BLE 4.2 sensor can send and receive messages through the RPi3B+ as a gateway. Bluetooth beacons that attempt to track your device require explicit permission as of v4.2. The LE Secure Connections pairing option is also available as of Bluetooth 4.2.
Performance
I was only able test the RPi3B+ for this article with a pre-release image with wireless not yet enabled and the CPU still clocked at 1.2GHz. A test with the new software image is coming soon, and the performance values for the RPi3B+ should improve significantly. As Table 1 shows, though, they are already impressive.
Table 1
RPi3B+ vs. RPi3B Test Results
RPi3B | RPi3B+ | Comment |
|
---|---|---|---|
Specifications |
|||
SoC |
Broadcom BCM2837 |
Broadcom BCM2837B0 |
Quad-core Cortex-A53 |
CPU |
Cortex-A53 at 1.2GHz |
Cortex-A53 at 1.4GHz |
RPi3B+ tested at 1.2GHz |
RAM |
1024MB LPDDR2 |
1024MB LPDDR2 |
– |
LAN |
10/100Mbps |
1,000Mbps |
USB 2.0 |
Power |
5V, 2.5A |
5V, 2.5A |
Micro-USB |
System |
|||
SysBench (seconds) (1) |
93.05 |
92.86 |
Slower is better |
SysBench (seconds) (2) |
372.09 |
371.34 |
Slower is better |
RAM |
|||
mbw, MEMCPY method (MiBps) |
694.80 |
785.59 |
Higher is better |
mbw, DUMB method (MiBps) |
721.43 |
807.20 |
Higher is better |
mbw, MCBLOCK method (MiBps) |
1,086.91 |
1,287.24 |
Higher is better |
Network (LAN) |
|||
iperf (Mbps) (3) |
94 |
319 |
Higher is better |
SD Card |
|||
hdparm, cached (MBps) |
601.8 |
600.0 |
Higher is better |
hdparm, disk reads (MBps) |
21.6 |
21.7 |
Higher is better |
Power |
|||
Idle |
4.2W |
7.6W |
– |
Under load |
11.7W |
14.0W |
During SysBench (4) |
(1) CPU – total time, 3 repeats with 4 threads(2) CPU – total time by event execution, 3 repeats with 4 threads(3) 3 repeats(4) 3 repeats with 4 threads |
Both the RPi3B and RPi3B+ devices were tested with a SanDisk SD card (class 10) and an EM 231 energy monitor by MK Electronics. A keyboard and HDMI and Ethernet cables were connected. The remote station in the LAN was a GigE port on a laptop connected with a gigabit switch by TP Link.
Interesting Facts
To run all functions of the new RPi3B+, you definitely need new software: It does not boot with NOOBS before version 2.7.0 dated March 14, 2018. The developers are also working on a firmware update for Raspbian Jessie. Other distributions, like LibreELEC and RetroPie, will follow suit in time.
The 40-pin GPIO header stayed the same, so all extension HATs fit. As with the RPi3B and Pi Zero W, Bluetooth is connected via the UART (PL011). If you use the UART through the GPIO header, you should note the known limitations of its mini UART. Alternatively, swap the two UARTs via overlay or disable Bluetooth [4].
The RUN header previously had two pins, of which one was ground suitable for mounting a reset button. However, the power supply remained switched on. With the RUN pin continuously grounded, the CPU was off for all intents and purposes, but the hardware still consumed power.
In the RPi3B+, the ground pin was removed from this header and a new PEN (power enable) pin was added. If you connect it to ground, it completely drains the power from the board. The board then transitions to the lowest consumption state possible, making it useful for projects that operate with a battery and wake up using a microcontroller.
« Previous 1 2 3 Next »
Buy this article as PDF
(incl. VAT)
Buy Linux Magazine
Subscribe to our Linux Newsletters
Find Linux and Open Source Jobs
Subscribe to our ADMIN Newsletters
Support Our Work
Linux Magazine content is made possible with support from readers like you. Please consider contributing when you’ve found an article to be beneficial.
News
-
So Long Neofetch and Thanks for the Info
Today is a day that every Linux user who enjoys bragging about their system(s) will mourn, as Neofetch has come to an end.
-
Ubuntu 24.04 Comes with a “Flaw"
If you're thinking you might want to upgrade from your current Ubuntu release to the latest, there's something you might want to consider before doing so.
-
Canonical Releases Ubuntu 24.04
After a brief pause because of the XZ vulnerability, Ubuntu 24.04 is now available for install.
-
Linux Servers Targeted by Akira Ransomware
A group of bad actors who have already extorted $42 million have their sights set on the Linux platform.
-
TUXEDO Computers Unveils Linux Laptop Featuring AMD Ryzen CPU
This latest release is the first laptop to include the new CPU from Ryzen and Linux preinstalled.
-
XZ Gets the All-Clear
The back door xz vulnerability has been officially reverted for Fedora 40 and versions 38 and 39 were never affected.
-
Canonical Collaborates with Qualcomm on New Venture
This new joint effort is geared toward bringing Ubuntu and Ubuntu Core to Qualcomm-powered devices.
-
Kodi 21.0 Open-Source Entertainment Hub Released
After a year of development, the award-winning Kodi cross-platform, media center software is now available with many new additions and improvements.
-
Linux Usage Increases in Two Key Areas
If market share is your thing, you'll be happy to know that Linux is on the rise in two areas that, if they keep climbing, could have serious meaning for Linux's future.
-
Vulnerability Discovered in xz Libraries
An urgent alert for Fedora 40 has been posted and users should pay attention.