Dashboard for RaspPi-controlled toy sailboat with Node-RED
Sail Away
With Node-RED, you can create a web dashboard that instructs a Raspberry Pi to set the rudder position on a toy sailboat.
My daughters and I have built a number of toy boat projects with an assortment of Arduino, ESP8266 (WiFi), Bluetooth, and radio frequency interference (RFI) components, but the version we created for this article using a Raspberry Pi and Node-RED [1] offers one of the simplest solutions. The sailboat uses a basic catamaran design with a Raspberry Pi mounting inside a waterproof container. With Node-RED dashboards, you can control the sailboat's rudder from a smartphone. The complete Node-RED logic comprises only six nodes.
Building the Sailboat
Of the many different building materials from which you could choose, K'Nex construction pieces [2] are lighter than either Lego or Meccano, and they allow you to create reasonably large structures with a minimum number of pieces. If you do not have access to K'Nex pieces, popsicle sticks and cardboard would offer a good low-cost solution.
To build the sailboat we used:
- K'Nex building pieces
- Four plastic bottles
- Small plastic container with a lid
- String
- Duct tape
- Garbage bag
- Low-torque servo
- Raspberry Pi Zero W or 3
- Small USB phone charger
The base of the sailboat was a rectangular structure with 16 water-facing K'Nex pieces that allowed plastic bottles to be duct-taped in place (Figure 1). A few K'Nex pieces created a compartment for the servo, and wire secured the servo in place. A rudder was built by screwing a small piece of wood into the servo arm (Figure 2). A garbage bag was cut to the required size and taped to the mast to form a sail. The boom had a swivel connection to the mast and guide ropes connected to both the boom and mast (Figure 3).
Servo and Rudder
Only very low torque servos can be connected directly to Raspberry Pi GPIO pins (Figure 4). An example of a low-torque servo would be the TowerPro SG90 [3] ($4), which has a torque of 25 oz/in (1.80 kg/cm). If you have servos with greater torque, you will need to use either a custom Raspberry Pi servo hat (there are some good ones on the market) or a separate power and ground circuit for the servo.
The WiringPi gpio
tool can be used to control the servo. This package is pre-installed on the Raspbian image, or it can be installed manually by entering:
sudo apt-get install -y wiringpi
Servos typically want a pulse frequency of 50Hz; however, the Raspberry Pi pulse width modulation (PWM) pins have a frequency of 19,200Hz, so some range definitions and scaling are required:
gpio -g mode 18 pwm #define pin 18 as the PWM pin gpio pwm-ms # use "mark space" mode gpio pwmc 192 # set freq as 19200 gpio pwmr 2000 # use a range of 2000
The gpio pwm
commands are not persistent after a reboot. A simple solution for this problem is to put the above commands in the Pi user login file $HOME/.bash_login
.
After running the PWM setup commands, you need to do some manual testing to define your various rudder (servo) positions (Figure 5), such as Hard Left, Hard Right, Easy Left, Easy Right, and Straight. The pwm
timing numbers will vary according to your requirements and the positioning of the servo arm. We used the commands
gpio -g pwm 18 200 #straight gpio -g pwm 18 260 #hard left gpio -g pwm 18 140 #hard right gpio -g pwm 18 230 #easy left gpio -g pwm 18 170 #easy right
for our sailboat.
Node-RED Logic and Dashboards
Node-RED is pre-installed on the Raspbian image, but it will need to be set to autostart on a Pi reboot with:
sudo systemctl enable nodered.service
The Node-RED web interface for configuration is accessed at http://localhost:1880 or http://<pi_ip_address>:1880. Selecting View | Dashboard brings up the options button on the far right (Figure 6), where you can define and change the web dashboard layout. To create logic, nodes are selected from the left node panel and dragged and dropped onto the center flow panel. Logic flow is then created by clicking and joining together the inputs and outputs on the nodes [4]. When a dashboard node is dropped onto the flow panel, it is added to the default web dashboard.
To call the gpio -g pwm
command, use the exec node (Figure 7). The button dashboard node will pass the defined payload value (e.g., a 260 is passed when the Hard Left button is pushed). The button's payload value is appended to the exec command to make a complete servo position command.
Once you have completed your logic setup, press the Deploy button on the top right to make your configuration live and ready to test.
Buy this article as PDF
(incl. VAT)
Buy Linux Magazine
Subscribe to our Linux Newsletters
Find Linux and Open Source Jobs
Subscribe to our ADMIN Newsletters
Support Our Work
Linux Magazine content is made possible with support from readers like you. Please consider contributing when you’ve found an article to be beneficial.
News
-
Canonical Releases Ubuntu 24.04
After a brief pause because of the XZ vulnerability, Ubuntu 24.04 is now available for install.
-
Linux Servers Targeted by Akira Ransomware
A group of bad actors who have already extorted $42 million have their sights set on the Linux platform.
-
TUXEDO Computers Unveils Linux Laptop Featuring AMD Ryzen CPU
This latest release is the first laptop to include the new CPU from Ryzen and Linux preinstalled.
-
XZ Gets the All-Clear
The back door xz vulnerability has been officially reverted for Fedora 40 and versions 38 and 39 were never affected.
-
Canonical Collaborates with Qualcomm on New Venture
This new joint effort is geared toward bringing Ubuntu and Ubuntu Core to Qualcomm-powered devices.
-
Kodi 21.0 Open-Source Entertainment Hub Released
After a year of development, the award-winning Kodi cross-platform, media center software is now available with many new additions and improvements.
-
Linux Usage Increases in Two Key Areas
If market share is your thing, you'll be happy to know that Linux is on the rise in two areas that, if they keep climbing, could have serious meaning for Linux's future.
-
Vulnerability Discovered in xz Libraries
An urgent alert for Fedora 40 has been posted and users should pay attention.
-
Canonical Bumps LTS Support to 12 years
If you're worried that your Ubuntu LTS release won't be supported long enough to last, Canonical has a surprise for you in the form of 12 years of security coverage.
-
Fedora 40 Beta Released Soon
With the official release of Fedora 40 coming in April, it's almost time to download the beta and see what's new.